ANSI A161.1 PDF

0 Comment

Buy ANSI A PERFORMANCE STANDARDS FOR KITCHEN AND VANITY CABINETS from SAI Global. Buy KCMA A Performance And Construction Standard For Kitchen And Vanity Cabinets from SAI Global. Kitchen and vanity cabinets bearing the ANSI/KCMA A certification seal have been extensively tested for their structural integrity, drawer.

Author: Arajind Katilar
Country: Turkey
Language: English (Spanish)
Genre: Automotive
Published (Last): 11 March 2016
Pages: 403
PDF File Size: 18.79 Mb
ePub File Size: 6.30 Mb
ISBN: 159-5-83988-421-3
Downloads: 67899
Price: Free* [*Free Regsitration Required]
Uploader: Jugar

Your recommendation is being sent! A 3 pound steel ball is “drop tested” against shelves, cabinet bottoms and drawer bodies to ensure cabinets will withstand dropping of cans and other items. The finish must then show no appreciable discoloration and no evidence of blistering, cold checking, or other film failure. The drawers must then remain operable with no failure in any part of the drawer assembly or operating system, and drawer bottoms must not be deflected to interfere with drawer operation.

To test the ability of the drawer-front assembly to withstand the impact of closing the drawer under normal use, a 3-pound weight is dropped 8 inches against the drawer assembly.

Share your thoughts with us in the comments below. To test the ability of the finish to w ithstand hot and cold cycles for prolonged periods, a cabinet door is placed in a hotbox at F and 70 percent relative humidity for one hour, removed and allowed to return to room temperature and humidity conditions, and then placed in a coldbox for one hour at -5F. The cycle is repeated five times.

Cabinets are impact tested by striking the center of a closed and open door with a 10 pound sand bag. To test the ability of doors, hinges, and means of attachment to withstand loading, 65 pounds of weight is applied on the door. For information on the certification or to locate a certified cabinet manufacturer, visit the Certifications portal at KCMA.

Installed wall cabinets are loaded with pounds to ensure that the cabinet will accept net loading in compliance with ANSI A A load of up to pounds is applied against the inside of cabinet fronts to ensure reliable front joints. To test the ability of the finish to withstand long periods of exposure to a detergent and water solution, a cabinet door edge is subjected to exposure to a standardized detergent formula for 24 hours. The exceptions are sink fronts and bases, oven cabinets and refrigerator cabinets.

To test the ability of the finish to withstand high heata cabinet door is placed in a hotbox at F and 70 percent relative humidity for 24 hours. The door edge must then show no delamination or swelling and no appreciable discoloration or evidence of blistering, checking, whitening, or other film failure.

  BALADA PARA ADELINA PIANO SHEET PDF

The strength behind certified cabinetry: ANSI/KCMA A | Woodworking Network

These include participation and review by consumer and supplier organizations, builders, remodelers, the U. Cabinet doors are weighted with 65 pounds and operated 10 times to test the ability of door and hinges to withstand loading. To test the ability of shelves, bottoms and drawer bottoms to withstand the dropping of cans and other items, a 3-pound steel ball is dropped from 6 inches above the surface.

In addition, mounted wall cabinets are gradually loaded to pounds to ensure no visible sign of failure in the cabinet or the mounting system. View the discussion thread. To test the ability of doors, door-holding devices, hinges and attachment devices to operate under the stress of normal use, doors are opened and closed through a full degree swing for 25, cycles. The door must remain weighted for 10 minutes, after which the door and hinges must show no visible signs of damage, and connections between cabinet-and-hinge and door-and-hinge must show no sign of looseness.

A hour soap and water solution test checks the finish’s ability to withstand exposure to detergents and moisture.

The strength behind certified cabinetry: ANSI/KCMA A161.1

The maximum number of products that can be compared is 4. Welcome to our redesigned homepage!

Scroll Down for more stories. A161. weighted door is slowly operated for 10 cycles from 90 degrees open to 20 degrees open, and returned to the degree position. Finish is exposed to vinegar, grape juice, olive oil, lemon juice, proof alcohol and more andi ensure no appreciable discoloration, stain or whitening of the finish occurs. These verify the structural integrity and strength of the cabinets.

KCMA has sponsored the nationally recognized cabinet testing and certification program for more than 45 years.

Doors are opened and closed for 25, cycles to ensure durability under the stress of normal usage. Cabinet finishes are inspected to ensure that stringent standards of appearance are also met.

Mastercraft Cabinets | KCMA Certification Program, ANSI Standards

To test the strength of base-front joints, a load of pounds is applied against the inside of cabinet-front stiles for cabinets with a asni rail, or pounds for cabinets without a16.11 drawer rail, to ensure reliable front joints that will not open during stress in service or during installation.

  CONVENIO DE TELEOPERADORES 2010 PDF

To a11.1 the ability of cabinet doors and connections to withstand impacts such as children may cause in falling against a cabinet, or running into it with a tricycle, a pound sandbag is used to strike the center of a closed cabinet door and repeated with the door opened to a degree angle.

A 3 pound weight is dropped 10 times against the drawer assembly to ensure that the drawer front assembly will withstand x161.1 impact of closing. Drawers and drawer mechanisms are tested at 15 pounds per aansi foot and operated through 25, opening and closing cycles to assure durability.

To be certified, cabinetry must first meet the following 14 construction requirements: On z161.1 cabinets, the shelves and bottoms are loaded at 15 pounds per square foot, with the weight maintained for seven days to ensure that there is a16.11 excessive deflection and no visible sign of joint separation or failure of any part of the cabinets or the mounting system.

To test the ability of the finish to withstand substances typically found in the kitchen and bath, exterior exposed surfaces of doors, front frames, drawer fronts and end panels are subjected to vinegar, lemon, orange and grape juices, tomato catsup, coffee, olive oil, and proof alcohol for 24 hours and to mustard for one hour. Your Email has been successfully sent! Please refine your selection. After the test the drawer must not be damaged and a1661.1 operate as before the test, with no visible sign of joint separation or failure of any part of the cabinet or mounting system.

Skip to main content. Have something to say? For more information on the certification process, or to find manufacturers of certified cabinetry, visit KCMA. After 10 drops, there must be no evidence of looseness or structural damage to the drawer-front assembly that impairs its operation.

To test the ability of drawers and drawer mechanisms to operate with loading during normal use, drawers are loaded at 15 pounds per square foot and operated through 25, cycles.

They should also be filled and sanded, edgebanded, or otherwise finished to ensure compliance with the performance standards.

This ensures the cabinets will live up to your expectations.