APM2509N DATASHEET PDF

0 Comment

Datasheet search engine for Electronic Components and Semiconductors. APMN data sheet, alldatasheet, free, databook. APMN parts, chips, ic, . PB: Plastic Bag. Lead Free Code. L: Lead Free Device Blank: Original Device. APMN UB: APMN. XXXXX. XXXXX – Date Code. Lead Free Code. advise customers to obtain the latest version of relevant information to verify before placing orders. APMNF. APMN. Handling Code. Temp. Range.

Author: JoJojora Mikajinn
Country: Tanzania
Language: English (Spanish)
Genre: Science
Published (Last): 12 August 2017
Pages: 185
PDF File Size: 5.87 Mb
ePub File Size: 19.43 Mb
ISBN: 973-6-51591-560-3
Downloads: 82603
Price: Free* [*Free Regsitration Required]
Uploader: Nikojin

Skill Information and Support G.

APMN Datasheet, PDF – Datasheet Search Engine

It’s tricky to troubleshoot problems like these, because there has generally been something that caused such a “catastrophic” failure. Dataasheet Posted by Kram. Look up the data sheet, and then use the diode mode on your multimeter to probe from gate to drain, gate to source.

Originally Posted by crashZ. This all of course assumes that the problem is what I described. When I “fixed” my board, I traced back to the fet because of one thing: I doubt it’s the VPU, but if it is, check this thread out for a theoretical fix: Q5 and Q6 are k 6k4.

How do I remove the mosfet? Stacker Watercooled windows7 ultimate 64 bit!!! Xpm2509n card is tripping the psu’s over current protection only turns on for a milisecond, have to reset with mains switch. All times are GMT I will have to get a picture. In retrospect, this is probably not a great idea, as I have no idea what the circuit topology of the card is, so I say don’t try this unless all other troubleshooting ratasheet fruitless JD. In this pcb layout would datashset both be N channel type?

  ELECTRICITY AND MAGNETISM NAYFEH PDF

I assume the vGPU inductor would be the 1R0 labled component, bottom right of the front pcb picture below between white connector and capacitor.

I ended up removing datashwet FET dafasheet, it looks like it can’t handle the current, I’m looking for another suitable replacement. Any help would be greatly appreciated. I’d start by using your multimeter to probe the legs of each fet. I had a similar issue, can you shoot a picture of the board?

Mine would apm250n, but would crap out and die after a few minutes, with severe heat issues. Zpm2509n n I just bought a new DELL SW monitor and was using it with my old Geforce for about 2 hours on my pc when I put on Call of Duty and suddenly when the game resolution changed the screen just remained black, I restarted the machine and the screen didn’t come on.

O it doest stay on long enough to burn anything: If any fet is conducting low R in both directions, it’s likely dead. My card was an eVGA gso. Im having some problems with finding datasheets: O I lifted the inductors – lead was easyer, I hate Jlead smd’s I got ohm on the good phases and on the dead phase.

APM2509N Datasheet PDF

I suspect it is more likely blown mosfets but not really sure how to test. Were you able to repair your card? I would really like a suggestion of a replacement, since I really have no idea with fets.

  KUPOPRODAJNI UGOVOR VOZILA PDF

Your DMM should beep or something, but only in one direction gate out, or gate independing on type of fet. Could this be the same issue people were having with nvidia gpu’s in laptops bga solder datassheet Those fets will be sort of You will probably need a hot air rework station to remove the fet from the board, since there has been solder datashet applied to the tab.

With 6pin cable removed, the psu doesnt trip, but screen stays black.

So I will need both type of fet: You were not supposed to see this. Found a few problems: Results 1 to 22 of Last edited by Kram; at I replaced one of the power FETs, and it booted right up. Anyways here is dattasheet image you requested.

As Largon has said, it’s going to suck if you’re trying to remove the FETs with just a soldering iron, the tabs that are attached to the apm2509m of the FET are going to be soldered down to the board, unless you have a hot air rework station, you’re likely going to do more harm than good The replacement I found was similar in specs, but obviously isn’t up to the task.

Swapped graphics card and pc works fine. The time now is