ASTM A – pdf – Download as PDF File .pdf), Text File .txt) or read online. ASTM A/AM Standard Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications. ASTM A/AM: Standard Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications.
|Published (Last):||19 October 2008|
|PDF File Size:||3.37 Mb|
|ePub File Size:||2.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
Three levels of acceptance standards are provided. Supplementary requirements are provided for alternative procedures. Combining values from the two systems may result in non-conformance with the aetm. A clean, easily interpreted trace pattern should be produced during the examination.
If s578 drop in back re? The Navic is a aastm, motorized, steerable scanner designed to carry multiple attachments used. Current edition approved Sept. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. A curve is then plotted showing the deviations from the above established 2: Available in both two-axis and three-axis instrument configurations and adaptable to cover a wide range of degree nozzle sizes, from 3″ upwards, on ferritic and austenitic materials.
It’s easy to join and it’s free. A has 3 different acceptance levels A, B, C. Supplementary requirements are provided for alternative procedures.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The holes may be drilled in the plate to be examined if they can be located without interfering with the use of the plate, in a prolongation of the plate to be examined, or in a reference block of the same nominal composition, and thermal treatment as the plate to be examined.
Use the transducers at their rated frequency. The transducer skew axis can also be adjusted, encoded and locked. All discontinuities causing complete loss of reflection shall be recorded. The supplement number shall be added for each supplementary requirement ordered. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Just to start you off in your standards selection review exercise: Close this window and log in. The Navic is capable of weld scanning girth welds and long seam weldsautomated corrosion mapping, and tank scanning. Link to Active This link will always route to the current Active version of the standard. Supplementary requirements are provided for examination of clad plate and for alternative procedures.
Posting Guidelines Promoting, selling, recruiting, coursework and thesis posting is forbidden. The method will detect internal discontinuities parallel to the rolled surfaces.
The method 5a78 detect internal discontinuities parallel to the rolled surfaces. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Condition local rough surfaces by grinding. The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned asrm this standard. An equivalent standard is one which covers the qualification and certification of ultrasonic nondestructive examination candidates and which is acceptable to the purchaser.
Link to Active This link will always route to a5788 current Active version of the standard. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Move the transducer away from the center of the discontinuity until the height of the back re? Where parallel path scanning is performed and recordable conditions as in 6. Register now while it’s still free! At each increment the ratio of the two signals is determined.
The material shall be held for metallurgical review by the purchaser and manufacturer. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. By joining you are opting in to receive e-mail. Q578 a suitable couplant such as water, soluble oil, or glycerin.
Digital Astmm may be defined in a number of different ways by analysts or enterprise a78 vendors. Download Now Defense manufacturing is all about project manufacturing and project accounting. Download Now A57 Paper: About Advertise Contact Login. Three levels of acceptance standards are provided. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. The holes may be drilled in the plate to a5778 examined if they can be located without interfering with the use of the plate, in a prolongation of the plate to be examined, or in a reference block of the same nominal composition and thermal treatment as the plate to be examined.
Are you an Engineering professional? The inspection shall be performed in an area free of operations that interfere with proper performance of the test.
Defense manufacturing is all about project manufacturing and project accounting. A is not only applicable to alloy clad plate but can also be applied to “normal” plate.