ASTM D(). Standard Guide for Testing Coating Powders and Powder Coatings. standard by ASTM International, 06/01/ View all product . Purchase your copy of ASTM D – 06() as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. Mitsubishi GT06 Autotitrator. P-E Headspace .. Coating. Provider. From ASTM. D 5 Samples from powder coating lot to be used. 5.
|Published (Last):||2 March 2006|
|PDF File Size:||8.53 Mb|
|ePub File Size:||9.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
The most widely recognized test for hardness is the pencil test. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.
Your Alert Profile lists the documents that will be monitored. Accelerated Environmental Exposure If need be, color can also 60 visually evaluated using Practice Dwhich determines the Munsell Coordinates of the color of a coated surface. Already Subscribed to this document. Many properties of powder coating?
On the other hand, if one needs to coat a part with sharp edges, a coating powder with relatively short? Your comments will receive careful consideration asrm a meeting of the responsible technical committee, which you may attend. Abrasion resistance Air blast abrasion tester Falling sand method Taber abraser Adhesion Tape adhesion Chemical resistance Household chemical resistance Detergent resistance Acid resistance Stains or reagents on wood substrates Chip resistance Gravelmeter Edge coverage Electrical insulation Ashm For a very smooth cured?
NOK 1 ,00 excl. There are many types of abrasion tests available and often one, more than the others, will best simulate the abrasion resistance required in 60 particular end use application.
This is true whether the test is an established test, like salt spray Practice Bor a new test developed to simulate an environmental service condition unique to one given industry. As the voice of the U. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
Selection of the methods to be followed must be governed by experience and the requirements in each individual case, together with agreement 006 the purchaser and the seller. Information on current test procedures for pipe and reinforced steel bar coating powders and powder coatings can be obtained through their respective ASTM Subcommittees, A If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
NOTE 4—The impact fusion resistance of a coating powder is dependent on many factors, not just its melt temperature. Place the pointer at this point. We have no amendments or corrections for this standard. Impact resistance has also been found to be a good indication of whether a coating powder has been adequately cured.
By design this guide does not purport to address test methods or procedures developed specifically for the functional powder coating market, those coating powders for application to pipe or reinforced steel bars rebar.
No other units of measurement are included in this standard. Some industries that is, automotive have also adopted the use of Knoop Indention Hardness. Start Webshop Product catalog Product presentation. Adhesion tests can also be used for testing the degree of attachment between a primer powder coating or other coating type and a second coat of coating powder that is, intercoat adhesion.
Where more than one test method is listed for the same characteristic, 0 attempt is made to indicate superiority of one method over another. Click to learn more. Standards Subsctiption may be d33451 perfect solution.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Interpretation of the test results will depend on the specific application in question and will also often depend on the chemistry of the coating powder used. Usage of paint systems is so varied that no one set of conditions length or place of exposure can be given in this guide to cover all situations.
The asgm power distribution of light from an enclosed carbon-arc is signi?
However, it is suggested adtm unless otherwise agreed upon, panels for outdoor exposure should be prepared in accordance with Section 21 of this guide. There is unfortunately, no one optimum P. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
The faster, easier way to work with standards. The type, application, and treatment of any undercoat system should be agreed upon between the purchaser and the seller. Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another.