0 Comment

Example of pitting after corrosion testing in accordance with ASTM G48 Method A . The test temperature of 22 °C is too aggressive for lean duplex grades such. Abstract ASTM G48 – “Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride. 1 These test methods are under the jurisdiction of ASTM Committee G01 on. Corrosion Results for ASTM G48 Standard Test Method for Pitting and Crevice.

Author: JoJoshura Yozshubar
Country: Belgium
Language: English (Spanish)
Genre: Photos
Published (Last): 25 February 2004
Pages: 177
PDF File Size: 3.96 Mb
ePub File Size: 11.8 Mb
ISBN: 170-9-54036-408-1
Downloads: 76106
Price: Free* [*Free Regsitration Required]
Uploader: Fenrile

Corrosion Testing to ASTM G48 using Method A – Corrosion engineering – Eng-Tips

NOTE asttm is important to record the means by which the presence of pits or crevices was assessed since, for example, small diameter pits or pits in a region of crevice attack that were not detected by a needle-point micrometer may be observed with a low-magni? Repeatability is within laboratory variability when the same operator uses the same equipment on identical specimens in sequential runs.

Download Now Defense manufacturing is all about project manufacturing and project accounting. Insulating sleeves shall be used around the bolt and the specimen shall be checked for electrical contact with the bolt. The purpose of A is to detect intermetallic phases. Yes, we did not add HCL to the test solution. Digital Transformation may be defined in a number of different ways by analysts or enterprise software vendors.


A number in parentheses indicates the year of last reapproval. There is not one single test that will accomplish both. In some cases, the crevice formers may become stained with corrosion products from the tested alloy. A reasonable test period is 72 h, although variations may be used at the discretion of the investigator and depend on the materials being evaluated.

The available pitting and crevice testing methods include: Where you cut a sample and grind the surfaces, no pickle or passivation allowed, and test in ferric chloride?

When using stainless and duplex steels, ASTM G48 is widely used to ensure the quality of the material and resistance to pitting and crevice corrosion.

Testing by ASTM G48 for Pitting and Crevice Corrosion

Method A — Ferric chloride pitting test. G48 Method A is commonly called out for cast superduplex stainless with a 24 hour test asgm at 50C and 24hrs. We follow a standard practice we have developed to minimize these variations and provide consistent data. Consequently, the degree of corrosion damage that occurs during testing will generally be greater than that in natural environments in any similar time period.

Asfm you sure that the temp is correct for the alloy? Originally approved in Download Now White Paper: This test period was evaluated by interlaboratory testing, Use plastic gloves to avoid hand contact with metal surfaces during this operation. This standard contains six methods, A through F. A more detailed examination will include the measurement of maximum pit depth, average pit depth, pit density, and crevice depth. Use the small O-ring or the No.


Log in to your subscription

There are several factors that can influence the ast, of methods; we can help you with this part of the process as well. Proceedings of an international conference Diverless and Deepwater Techology: Rubber bands shall be one No. There are 6 Methods: We hired an independant 3rd party to perform xstm testing to G48 Method A as per client requirements but by mistake 3rd party booked the specimen to A and testing was done also to A and result is OK.

The sharp edges of a specimen should be rounded to avoid cutting rubber bands or O-rings. The torque on the bolt in?

NOTE 17— a Titanium bolts, nuts, and? NOTE 7—Rubber bands or O-rings can be boiled in water prior to use to ensure the removal of water-soluble ingredients that might affect corrosion. Resources Digital Transformation may be defined in a number of different ways by analysts or wstm software vendors. NOTE 20—The torque of 1.

Or at least do micros. Promoting, selling, recruiting, coursework and thesis posting is forbidden. The oil and gas industry has spent a great deal of time and effort since the 80s in arriving at a standardised G48 test for duplex.

The three crevice tests, Methods B, D and F, vary in crevice-former contact area adtm crevice gap thickness.