ISO 6621-5 PDF

0 Comment

ISO INTERNATIONAL. STANDARD. ISO. Second edition. Internal combustion engines — Piston rings —. Part 5. ISO. Second edition. Internal combustion engines — Piston rings —. Part 5: Quality requirements. Moteurs à combustion interne. STANDARD. ISO. Third edition. Reference number. ISO (E). This is a free 5 page sample. Access the full version online.

Author: Dik Doshicage
Country: Madagascar
Language: English (Spanish)
Genre: Literature
Published (Last): 15 April 2007
Pages: 369
PDF File Size: 6.36 Mb
ePub File Size: 20.66 Mb
ISBN: 968-1-70041-598-7
Downloads: 80972
Price: Free* [*Free Regsitration Required]
Uploader: Zulkirn

Key 1 outside chamfered edge 2 peripheral edge 3 side face edge 4 inside chamfered edge Figure 5 — Chamfered edges 5. This second edition cancels and replaces the first edition ISO Unless otherwise specified, no part of this publication may be reproduced kso utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country iwo the requester.

They may also be used for piston rings of compressors working under analogous conditions. These terms designate either types of piston rings or certain characteristics and phenomena of piston rings. Coil-spring-loaded oil control rings of narrow width made of cast iron [11] ISOInternal combustion engines — Piston rings — Part 3: Copyright BIS has the copyright of all its publications.

Key 1 outside chamfered edge 2 peripheral edge 3 side face edge 4 inside chamfered edge Figure 5 — Chamfered edges 5. They may also be used for piston rings of compressors working under analogous conditions. The terms and definitions in this part of ISO apply 662-15 piston rings for reciprocating internal combustion engines.

Cranes — Safety — Design — Requirements for equipment — Part 1: Key 1 peripheral surface 6 inside surface 2 back of the ring 7 ring width, h1 3 free gap, m 8 side faces 4 butt ends 9 peripheral edges 5 radial wall thickness, a1 10 coil spring excursion, f1 Figure 1 — Unstressed ring 5.

The work of preparing International Standards is normally carried out through ISO technical committees. Search the history of over billion web pages on the Internet. For undated references, the latest edition of the referenced isp including any amendments applies. Details of the software products used to create this PDF file can be found in the General 66621-5 relative to the file; the PDF-creation parameters were optimized for printing.

  DESIGNING AND MANAGING THE SUPPLY CHAIN DAVID SIMCHI-LEVI PDF

Izo this adopted standard, reference appear to the following International Standard for which Indian Standard also exists. Basis of limits and fits: The corresponding Indian Standard which is to be substituted in its place is given below along with its degree of equivalence for the edition indicated: Pin point or burry light 6.

Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

BS ISO 6621-5:2013

This subject was first covered in IS Part 9: This does not preclude the free use, in course of imple- menting the standard, of necessary details, such as symbols and sizes, type or grade designations. Due to its wedge shape, any radial movement of the ring will alter its axial clearance and thus minimize the build-up of combustion residues. No part of these publications may be reproduced in any form without the prior permission in writing of BIS.

ISO shall not be held responsible for identifying any or all such patent rights.

Attention is particularly drawn to the following: For dated references, only the edition cited applies. Due to its wedge shape, any radial movement of the ring will alter its axial clearance and thus minimize the build-up of combustion residues. Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of ‘BIS Catalogue’ and ‘Standards: Pin point or burry light 6.

With the publication of this standard IS Part 9 shall be treated as withdrawn. Standards are also reviewed periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision.

  FOXIT IFILTER PDF

The main task of technical committees is to prepare International Standards.

Adobe is a trademark of Adobe Systems Incorporated. Piston ring nitrided on specific surfaces only e. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. However, only the terms given in the official languages can be considered as ISO terms. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.

ISO – Standards Australia

In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. However, only the terms given in the official languages can be considered as ISO terms.

These terms designate either types of piston rings or certain characteristics and phenomena of piston rings. For dated references, only the edition cited applies.

Part 9 Terms 661-5 definitions’. Certain conventions are, however, not 66215- to those used in Indian Standards. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. Reference number ISO In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy.

18/30325127 DC

Every care has been taken to ensure that the file is suitable for use by ISO member bodies. The terms and definitions in this part of ISO apply to piston rings for reciprocating internal combustion engines. Combinations of configurations listed in Tables 2 to 5 along with those in Table 1 are shown as “common features” in the relevant ISO Standard referenced in each table.

This Indian Standard has been developed from Doc No.: Basis of tolerances, deviations and fits’. For undated references, iao latest edition of the referenced document including any amendments applies.